| 1. | Load peripheral Disk in Drive 0 with SSW 1 Up. | |
| 2. | After the Tone, enter | MRAXXX |
| 3. | Press Start | MRAXXX is loaded
Data Display is 008E
Idle LED is on |
| 4. | Press Start | MRAXXX is run
Data Display is 008A
Idle LED is on |
| 5. | Press Start | RRAXXX is loaded
Data Display is 008E
Idle LED is on |
| 6. | Press Start | RRAXXX is run
Data Display is 008A
Idle LED is on |
| 7. | Press Start | SKIPAX is loaded
Data Display is 008E
Idle LED is on |
| 8. | Press Start | First Part of SKIPAX is run
Data Display is 02F3
Idle LED is on |
| 9. | Press IR Down | Data Display is CE09 |
| 10. | Set SSW 1,2 & 4 Up
Set SSW 3 Down | |
| 11. | Press Start | Second Part of SKIPAX is run
Data Display is 030E
Idle LED is on |
| 12. | Press IR Down | Data Display is CE0A |
| 13. | Set SSW 1,2 & 4 Down
Set SSW 3 Up | |
| 14. | Press Start | Last Part of SKIPAX is run
Idle LED is on |
As SSW 1 is Down, the System automatically Loads and Runs the Tests SHIFTA, PIFAXX, BYTEAX and MEMAXX:
Continue from Step 23 unless you want to run these Tests manually, in which case, continue from step 15. |
| 15. | Press Start | SHIFTA is loaded
Data Display is 008E
Idle LED is on |
| 16. | Press Start | SHIFTA is run
Data Display is 008A
Idle LED is on |
| 17. | Press Start | PIFAXX is loaded
Data Display is 008E
Idle LED is on |
| 18. | Press Start | PIFAXX is run (Takes approx. 30 seconds)
Data Display is 008A
Idle LED is on |
| 19. | Press Start | BYTEAX is loaded
Data Display is 008E
Idle LED is on |
| 20. | Press Start | BYTEAX is run
Data Display is 008A
Idle LED is on |
| 21. | Press Start | MEMAXX is loaded
Data Display is 008E
Idle LED is on |
| 22. | Press Start | MEMAXX is run
Data Display is 0260
Idle LED is on |
| 23. | Set SSW 1 Up | |
| 24. | Set A Down | Data Display is 03E0
(First Test Memory Address) |
| 25. | Set X Down | Data Display shows size of Memory
8K = 1FFF 40K = 9FFF
16K = 3FFF 48K = BFFF
24K = 5FFF 56K = DFFF
32K = 7FFF 64K = FFFF |
| 26. | Press Start | MEMAXX is run
(Takes approx. 90 Seconds)
Data Display is 008A
Idle LED is on |
| 27. | Press Start | ROMAXX is loaded
Data Display is 008E
Idle LED is on |
| 28. | Press Start | ROMAXX is run
Data Display is 023B
Idle LED is on |
| 29. | Set Mode to Halt | Idle LED goes off |
| 30. | Press Load Switch Up | |
| 31. | Set Mode to Run | |
| 32. | Press Start | ROMAC is loaded
Data Display is 008A
Idle LED is on |
| 33. | Press Start | M980R is loaded
Data Display is 008E
Idle LED is on |
| 34. | Press Start | M980R is run
Data Display is 0242
Idle LED is on |
| 35. | Set Data Switches to Memory Size (from Step 25) | |
| 36. | Press A Up | |
| 37. | Set SSW 1 Up | |
| 38. | Press Start | M980R is run
This Test takes the following times to complete
Memory Size 0-24K = 1 Memory PCB = Run for 3 Minutes
Memory Size 24-48K = 2 Memory PCB's = Run for 6 Minutes
Memory Size 48-64K = 3 Memory PCB's = Run for 9 Minutes |
| 39. | To stop Test set SSW 1 Down. | Data Display should be 0299
If Idle LED comes on, refer to TI Manual 961961-770 CPUPAT. | |
(0) No Comments. Start a discussion...